Next: , Previous: , Up: Top   [Contents][Index]

2 Building the Package

This chapter contains a detailed list of steps you need to undertake in order to configure and build the package.

  1. Make sure you have the necessary software installed.

    To build mailfromd you will need to have following packages on your machine:

    1. GNU mailutils version 3.3 or newer.

      GNU mailutils is a general-purpose library for handling electronic mail. It is available from

    2. GNU adns library, version 1.5.1 or newer.

      GNU adns is an advanced DNS client library. The recent version can be downloaded from Visit, for more information.

    3. A DBM library. Mailfromd is able to link with any flavor of DBM supported by GNU mailutils. As of version 9.0 it will refuse to build without DBM. By default, configure will try to find the best implementation installed on your machine (preference is given to Berkeley DB) and will use it. You can, however, explicitly specify which implementation you want to use. To do so, use the --with-dbm configure option. Its argument specifies the type of database to use. It must be one of the types supported by GNU mailutils. At the time of this writing, these are:

      Berkeley DB (versions 2 to 6).


      GNU DBM.


      Kyoto Cabinet


      Tokyo Cabinet



      To check what database types are supported by your version of mailutils, run the following command:

      $ mailutils dbd gdbm kc tc ndbm

      For backward compatibility, configure accepts the following two options:


      Same as --with-dbm=gdbm.


      Same as --with-dbm=bdb.

      For Sendmail users, it often makes sense to configure mailfromd to use the same database flavor as sendmail. The following table will help you do that. The column ‘DB type’ lists types of DBM databases supported by mailfromd. The column ‘confMAPDEF’ lists the value of confMAPDEF Sendmail configuration macro corresponding to that database type. The column ‘configure option’ contains the corresponding option to configure.

      DB typeconfMAPDEFconfigure option
      Berkeley DB-NNEWDB--with-dbm=bdb
  2. Decide what user privileges will be used to run mailfromd

    After startup, the program drops root privileges. By default, it switches to the privileges of user ‘mail’, group ‘mail’. If there is no such user on your system, or you wish to use another user account for this purpose, override it using DEFAULT_USER environment variable. For example for mailfromd to run as user ‘nobody’, use

    ./configure DEFAULT_USER=nobody

    The user name can also be changed at run-time (see --user).

  3. Decide where to install mailfromd and where its filter script and data files will be located.

    As usual, the default value for the installation prefix is /usr/local. If it does not suit you, specify another location using --prefix option, e.g.: ‘--prefix=/usr’.

    During installation phase, the build system will install several files. These files are:


    Main daemon. See mailfromd.


    Default main filter script file. It is installed only if it is not already there. Thus, if you are upgrading to a newer version of mailfromd, your old script file will be preserved with all your changes.

    See MFL, for a description of the mail filtering language.


    MFL modules. See Modules.


    Default preprocessor setup file. See Preprocessor.


    Documentation files.


    MTA simulator program for testing mailfromd scripts. See mtasim.


    Pmilter multiplexor for MeTA1. See pmult. It is build only if MeTA1 version ‘PreAlpha29.0’ or newer is installed on the system. You may disable it by using the --disable-pmilter command line option.

    When testing for MeTA1 presence, configure assumes its default location. If it is not found there, inform configure about its actual location by using the following option:


    where prefix stands for the MeTA1 installation prefix.

    It is advisable to use the same settings for file name prefixes as those you used when configuring mailutils. In particular, try to use the same --sysconfdir, since it will facilitate configuring the whole system.

    Another important point is location of local state directory, i.e. a directory where mailfromd keeps its data files (e.g. communication socket, PID-file and database files). By default, its full name is localstatedir/mailfromd. You can change it by setting DEFAULT_STATE_DIR configuration variable. This value can be changed at run-time using the state-directory configuration statement (see state-directory). To inspect the actual value of the local state directory, run

    mailfromd --no-config --show-defaults | grep '^statedir:'

    See Examining Defaults, for information about the --show-defaults option.

  4. Select default communication socket. This is the socket used to communicate with MTA, in the usual Milter port notation (see milter port specification). If the socket name does not begin with a protocol or directory separator, it is assumed to be a UNIX socket, located in the local state directory. The default value is mailfrom, which is equivalent to unix:localstatedir/mailfromd/mailfrom.

    To alter this, use DEFAULT_SOCKET environment variable, e.g.:

    ./configure DEFAULT_SOCKET=inet:999@localhost

    The communication socket can be changed at run time using --port command line option (see --port) or the listen configuration statement (see listen).

  5. Select default expiration interval. Expiration interval defines the period of time during which a record in the mailfromd database is considered valid. It is described in more detail in Databases. The default value is 86400 seconds, i.e. 24 hours. It is OK for most sites. If, however, you wish to change it, use DEFAULT_EXPIRE_INTERVAL environment variable.

    The DEFAULT_EXPIRE_RATES_INTERVAL variable sets default expiration time for mail rate database (see Rate limiting functions).

    Expiration settings can be changed at run time using database statement in the mailfromd configuration file (see conf-database).

  6. Select a syslog implementation to use.

    Mailfromd uses syslog for diagnostics output. The default syslog implementation on most systems (most notably, on GNU/Linux) uses blocking AF_UNIX SOCK_DGRAM sockets. As a result, when an application calls syslog(), and syslogd is not responding and the socket buffers get full, the application will hang.

    For mailfromd, as for any daemon, it is more important that it continue to run, than that it continue to log. For this purpose, mailfromd is shipped with a non-blocking syslog implementation by Simon Kelley. This implementation, instead of blocking, buffers log lines in memory. When the buffer log overflows, some lines are lost, but the daemon continues to run. When lines are lost, this fact is logged with a message of the form:

       async_syslog overflow: 5 log entries lost

    To enable this implementation, configure the package with --enable-syslog-async option, e.g.:

    ./configure --enable-syslog-async

    Additionally, you can instruct mailfromd to use asynchronous syslog by default. To do so, set DEFAULT_SYSLOG_ASYNC to 1, as shown in example below:

    ./configure --enable-syslog-async DEFAULT_SYSLOG_ASYNC=1

    You will be able to override these defaults at run-time by using the --logger command line option (see Logging and Debugging).

  7. Run configure with all the desired options.

    For example, the following command:

    ./configure DEFAULT_SOCKET=inet:999@localhost --with-berkeley-db=3

    will configure the package to use Berkeley DB database, version 2, and ‘inet:999@localhost’ as the default communication socket.

    At the end of its run configure will print a concise summary of its configuration settings. It looks like that (with the long lines being split for readability):

    Mailfromd configured with the following settings:
    Mailutils version......................... 3.15
    External preprocessor..................... /usr/bin/m4 -s
    DBM version............................... Berkeley DB v. 3
    Default user.............................. mail
    State directory...........................
    Socket.................................... mailfrom
    Expiration interval....................... 86400
    Compile asynchronous syslog............... no
    Readline (for mtasim)..................... yes
    Documentation rendition type.............. PROOF
    Enable pmilter support.................... no
    Enable GeoIP2 support..................... no
    Enable DKIM support....................... yes
    IPv6 support.............................. yes

    Make sure these settings satisfy your needs. If they do not, reconfigure the package with the right options.

  8. Run make.
  9. Run make install.
  10. Make sure localstatedir/mailfromd has the right owner and mode.
  11. Examine filter script file (sysconfdir/mailfromd.mfl) and edit it, if necessary.
  12. If you are upgrading from an earlier release of Mailfromd, refer to Upgrading, for detailed instructions.

Next: , Previous: , Up: Top   [Contents][Index]